台灣鈷領產品型錄

16 GU 500 Universal drills ≤500 ≤1000 ≤850 ≤1000 ≤700 ≤850 ≤1000 ≤1000 ≤1400 ≤850 ≤1000 ≤1400 ≤1000 ≤1400 ≤850 ≤1400 ≤1400 ≤350 HB ≤48 HRC ≤66 HRC ≤900 ≤1100 ≤1500 ≤240 HB ≤350 HB ≤240 HB ≤350 HB ≤350 HB ≤220 HB ≤300 HB ≤1000 ≤1400 ≤2000 ≤850 ≤1400 ≤400 ≤650 ≤600 ≤600 ≤400 ≤500 ≤600 ≤600 ≤600 ≤850 ≤850 ≤1000 ≤150 ≤100 ≤1000 ≤1000 GU 500 Universal drills All data are approximate values. The actually achievable cu�ng speeds and feed rates depend on the respec�ve machining condi�ons. We recommend suitable drilling trials. To select the op�mal tool and the recommended machining parameters for your applica�on, please also use the electronic version of the GühringNavigator on the internet: www.guehring.com . Material group Material examples Figures in bold = material no. to DIN EN 10 027 Tensile strength (N/mm²) Hardness Coolant Common structural steels 1.0035 S185(St33), 1.0486 P275N(StE285), 1.0345 P235GH(H1), 1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) Free-cu�ng steels 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) Unalloyed heat-treatable steels 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) Alloyed heat-treatable steels 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 Unalloyed case hard. steels 1.0301 (C10), 1.1121 C10E (Ck10) Alloyed case hardened steels 1.7276 10CrMo11, 1.5125 11MnSi6 1.5752 15NiCr13, 1.7131 16MnCr5, 1.7264 20CrMo5 Nitriding steels 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 Tool steels 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 High speed steels 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 Spring steels 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) Hardened steels – Stainless steels, sulphured 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 austeni�c 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) martensi�c 1.4057 X20CrNi172 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Cast iron iron 0.6010 EN-GJL-100 (GG10), 0.6020 EN-GJL-200 (GG20) 0.6025 EN-GJL-250 (GG25), 0.6035 EN-GJL-350 (GG35) Spheroidal graphite iron and 0.7050 EN-GJS-500-7 (GGG50), 0.8035 EN-GJMW-350-4 (GTW35) malleable cast iron 0.7070 EN-GJS-700-2 (GGG70), 0.8170 EN-GJMB-700-2 (GTS70) Chilled cast iron – New cast materials GGV EN-GJV250 (GGV25), EN-GJV350 (GGV35) EN-GJV400 (GGV40), EN-GJV500 (GGV50), SiMo 6 New cast materials ADI EN-GJS-800-8 (ADI800), EN-GJS-1000-5 (ADI1000) EN-GJS-1200-2 (ADI1200), EN-GJS-1400-1 (ADI1400) Special alloys Nimonic, Inconel, Monel, Hastelloy Ti and Ti alloys 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 Aluminium and Al alloys 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 Al wrought alloys 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 Al cast alloys ≤ 10 % Si 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 ≤ 24 % Si 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg Magnesium alloys 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 Copper, low-alloyed 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb Brass, short-chipping 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 long-chipping 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 Bronze, short-chipping 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb Bronze, long-chipping 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Duroplas�cs Bakelit, Resopal, Per�nax, Moltopren Thermoplas�cs Plexiglass, Hostalen, Novodur, Makralon Kevlar Kevlar Glass, carbon concent. plas�cs GRP/CFRP Ar�cle no. Standard/DIN Tool material Surface Type Std. range page 一般結構用鋼 易削鋼 碳鋼 合金鋼 低碳鋼 表面硬化 合金鋼 表面硬化 氮化鋼 工具鋼 高速鋼 彈簧鋼 高度硬鋼 不鏽鋼 鑄鐵 球墨鑄鐵 冷鍛鑄鐵 蠕墨鑄鐵 等溫淬火球墨鑄鐵 特殊合金 鈦及鈦合金 鋁及鋁合金 鍛造鋁合金 鑄鋁 鎂合金 純銅 紅銅 黃銅 青銅 短屑型 青銅 長屑型 硬質塑膠 玻璃纖維 碳纖維 杜邦 克維拉纖維 熱塑性塑膠 9 Drill Ø mm Feed column no. 1 2 3 4 5 6 7 8 9 f (mm/rev.) 5.00 0.040 0.050 0.063 0.080 0.100 0.125 0.160 0.200 0.250 6.30 0.050 0.063 0.080 0.100 0.125 0.160 0.200 0.250 0.315 8.00 0.063 0.080 0.100 0.125 0.160 0.200 0.250 0.315 0.315 10.00 0.080 0.100 0.125 0.160 0.200 0.250 0.315 0.400 0.400 12.50 0.080 0.100 0.125 0.160 0.200 0.250 0.315 0.400 0.500 16.00 0.100 0.125 0.160 0.200 0.250 0.315 0.400 0.500 0.630 20.00 0.125 0.160 0.200 0.250 0.315 0.400 0.500 0.630 0.630 25.00 0.160 0.200 0.250 0.315 0.400 0.500 0.630 0.800 0.800 31.50 0.160 0.200 0.250 0.315 0.400 0.500 0.630 0.800 1.000 40.00 0.200 0.250 0.315 0.400 0.500 0.630 0.800 1.000 1.250 50.00 0.250 0.310 0.400 0.500 0.630 0.800 1.000 1.250 1.250 63.00 0.315 0.400 0.500 0.630 0.800 1.000 1.250 1.600 1.600 80.00 0.400 0.500 0.630 0.800 1.000 1.250 1.600 1.600 2.000 Coolant: Air Oil Soluble oil 空氣 油性切削液 水溶性切削液